The first significant development in the processing of corrugated sheet steel
since 1844
UltraSHEET™ is a corrugated steel panel produced by the unique patented UltraSTEEL™ process developed within The Hadley Group.
UltraSHEET™ is suitable for all applications where standard corrugated steel sheet profiles are specified. Ideal for the construction of most basic utility/storage shelters to purpose designed dwellings and elevations calling for a low cost but visually attractive alternative to standard corrugated sheet products. The striking aesthetic qualities of UltraSHEET™ will provide architects and specifiers with an exciting alternative to other external cladding products.
UltraSHEET™ is an internationally patented method of altering the surface of cold rollformed steel and thereby improving its inherent strength and appearance
USAGE: Utility Buildings/Garages/Barns/General Purpose Storage/Silos
ADVANTAGES: Added Strength Low Maintenance Galvanised or Polyester/Coated Noise Reduction Identity
PROCESS: Utilising the latest coil-fed manufacturing plant enables us to supply sheets in any length from 4' 0" (1220mm) to30' 0" (9144mm). Rolled to customers specified requirements.
GALVANISED
All our galvanised sheets are manufactured from full prime quality hot dip zinc coated steel.
Substrate: FEP026 to EN1 0142:1991
Surface finish: Bright spangle
MATERIALS AVAILABLE
200 micron
PVC Plastisol Coated
Polyester Coated
Aluminium
Stainless Steel
All corrugated sheets are manufactured to the tolerances specified within BS 3083 : 1988,
Quality assurance is central to the manufacturing philosophy of the company which conforms to BS EN ISO 9002 1994 the international standard for quality control systems.
IDENTIFICATION
Identification and full traceability are maintained by ink jet marking sheets with the British Standard number together with the week and year of manufacture,
INTELLECTUAL PROPERTIES
UltraSTEEL™ and UltraSHEET™ are registered trade marks of The Hadley Group and are protected by the following patents:
GB 2095595B
GB2272662
GB Reg , Des, 2027271
Int. Pat. App W094/12294
Quality assurance is central to the manufacturing philosophy of the company which conforms to BS EN ISO 9002 1994 the international standard for quality control systems.
ACCESSORIES: -
In addition to the wide range of sheeting available we are able to offer flashings, trims and ridges as required:
CORNER FLASHINGS: 15",18" &24" GIRTH,
"Z" FLASHINGS: 15",18" &24" GIRTH,
RIDGE FLASHINGS: 15",18"&24" GIRTH,
ROLL TOP RIDGES: 15" GIRTH,
SHEET LAYING
In order to ensure a watertight skin to the building, it is essential that the correct installation and fixing procedures are followed. To prevent the ingress of driving rain, side laps should be sealed and face away from the prevailing wind. In all cladding applications adequate end lap is critical. For roofing applications, the end lap is largely dependent upon the roof pitch. Please refer to the table below for guidance.
ILLUSTRATION: TYPICAL SIDE-LAP DETAILS
SHEET LAYING
In order to ensure a watertight skin to the building, it is essential that the correct installation and fixing procedures are followed. To prevent the ingress of driving rain, side laps should be sealed and face away from the prevailing wind. In all cladding applications adequate end lap is critical. For roofing applications, the end lap is largely dependent upon the roof pitch. Please refer to the table below for guidance.
ILLUSTRATION: TYPICAL SIDE-LAP DETAILS
FIXING
Primary fasteners should be fixed through the centre of every other valley at each purlin, except at end laps where fasteners should be placed in every valley. All holes should be drilled and not punched and resultant swarf removed.
It is important to ensure that correct tightening torque is applied to the fastener to obtain maximum sealing and holding action. The above details are based upon experience, however sheeting contractors may adopt their own fixing methods but the Health and Safety Executive requirements must be satisfied.
